2

Go Kart Clutch | Available to Buy Online

The most commonly used Go Kart Clutch is the centrifugal clutch. These items join two shafts together to help keep an internal combustion engine running when the output shaft of the engine is suddenly stopped, or when the output shaft is slowed down considerably.

It accomplishes this task by disengaging the loads whenever the engine is just starting up after being stopped, and when the engine is idling. The clutch keeps the engine running, and it allows the vehicle that it is placed on to have increased speed, increased power, and a faster response time for speed pick up, and for slowing down.

Top Go Kart Clutch

The following centrifugal clutch assemblies stood out to me because of their design, the quality of the materials used to construct them, and the reliability they have shown throughout time. I like items that last a long time because they allow me to get the most from my money. These items all impressed me in different ways.

1) Centrifugal Clutch 2/4” Bore #35 Chain 12T For Go Kart Mini Bike Engine ¾ Bar

Centrifugal Clutch 2/4” Bore #35 Chain 12T For Go Kart Mini Bike Engine ¾ Bar

> Check Out Verified Customer Reviews and Ratings <<

This is a twelve tooth Centrifugal clutch that fits a number thirty five chain. The clutch uses a key stock to enable you to bolt it to the shaft of the engine.  It is imperative that you use the proper length key stock to hold the clutch in place. If your key stock is too small it will wiggle and this motion can cause you to end up having to replace your drive shaft. If the key stock is too large it simply will not go into the hole.

This clutch requires a 3/16 key stock. The bore size on this clutch is substantial so that it enables it to be placed on larger engines. Once this clutch I properly installed on the shaft of the engine you will can expect to get many years of service from it.

You have to maintain the clutch properly by keeping it properly oiled, but if you do, and if you use the proper driving habits this clutch will not need replaced quickly. The clutch is designed to not be affected by moisture, but if the clutch is immersed in water it might still be damaged. 

Check Latest Price and Stock

 

2) GoPowerSports Go Kart Mini Bike 10T Centrifugal Clutch ¾, 41/420

GoPowerSports Go Kart Mini Bike 10T Centrifugal Clutch 3/4, 41/420 This 10T sprocket fits a 41/420 chain. It has a ¾” bore and was specifically designed to be used on engines that are anywhere from two horsepower to seven horsepower engines. It has a built in 3/16” key so you will not have to worry about losing your key.

Your go kart engine will run longer and last longer because this clutch is perfectly designed to gradually introduce the load that is placed on the engine and keep the motor from stalling. This particular clutch is not too hard on the pocket book and it is one of the most effective clutches being sold.

>> Check Out Verified Customer Reviews and Ratings <<

They are very simple to install because they slip on and are held in place using key stock of the proper diameter. This type of clutch fits on a chain and not on a v-belt. It has teeth that help grip the chain and pull it around without allowing the chain to slip off of the clutch assembly.

You want to keep the clutch oiled properly so that it engages the engine more quickly. The process of oiling also allows the engine to be engaged at a higher RPM, and that increases the speed of the go kart of mini bike the clutch assembly is installed on. 

Check Latest Price and Stock

 

3) Go Kart/Mini Bike Clutch #41 Chain 3/4 Bore

Go kart / Mini Bike Clutch # 41 chain 3/4 Bore This clutch is manufactured to meet or exceed OEM specifications for this type of item. This particular clutch is designed to be bi-directional, so it can be mounted inboard, or outboard. It will easily fit onto the shaft of a ten horsepower engine.

The manufacturer supplies a complete with a one year warranty. That shows you that the manufacturer has complete confidence in the piece of equipment, and they do not expect you to have any trouble from it. The centrifugal clutch assemblies are made to be less troublesome than some of the other types of clutches sold on the market.

>> Check Out Verified Customer Reviews and Ratings <<

You will love the fact that you do not have to oil this piece of equipment, but if you do oil it then you can expect to get greater speed from your riding machine because oiling the clutch allows the engine to be engaged smoothly at a higher RPM.

You do not lose speed when you shift gears so you build speed faster, and maintain a faster speed because the clutch does not get over heated as easily. You will love the quality and the low maintenance that this important piece provides to you. 

Check Latest Price and Stock

 

4) Go Kart / Mini Bike Clutch #35 Chain 5/8 Bore

Go kart / Mini Bike Clutch # 35 chain 5/8 Bore Eleven teeth on the back side of this clutch are properly positioned to grip a number thirty five chain and pull it through without letting the chain slip. The carbide steel that this item is made from is a hardened steel manufactured to withstand high temperatures without overheating.

Some other clutch assemblies are made from cast iron, but cast iron is very brittle and the clutches rust easily and break easily. The carbide steel is very strong and will last for many years. The steel will rust but it is designed to resist rusting.

>> Check Out Verified Customer Reviews and Ratings <<

To prevent rusting you can keep the clutch properly oiled, and store the bike it is on inside instead of outside in the weather. This is a very low cost item, and you can expect to get several years worth of service from the clutch before it has to be replaced.

Taking proper care of your bike and chain that the clutch is installed on will increase the lifetime of the piece of equipment. When you do have to replace it you will not need any specialized tools to change it out. 

Check Latest Price and Stock

 

5) Hotouch Go-Kart Mini-Bike Clutch, Centrifugal 10T, ¾” Bore #40/41/420 Chain

Hotouch Go-Kart Mini-Bike Clutch, Centrifugal 10T, 3/4 In order to mount this clutch onto the crankshaft you use the bolt and washer that is included in the package. It will easily fit onto and power engines that are three and one half horsepower up to engines that are seven horsepower. It easily works on Honda and the Honda cloned engines from the two horsepower to the six and one half horsepower engines. Specifically it fits the following Honda engines: 

  • GC160
  • GC190
  • GX120
  • GX140
  • GX160
  • GX200

>>Check Out Verified Customer Reviews and Ratings <<

The clutch also works on Tecumseh engines that are less than a six and one half horsepower engine that has a three quarters of an inch shaft. It will work with Briggs and Stratton engines that have a three and one half quarter inch shaft and is no greater than a six and one half horsepower.

Keep in mind that this type of clutch is designed to be used on a vehicle that has tires that are not larger than fifteen inches in height. If you have a live axle on your go kart you will need to have a sixty tooth sprocket in place for proper function. 

Check Latest Price and Stock

 

6) Go Kart Torque Converter CVT Clutch ¾” Comet Tav2 30-75 218353A Manco 12T #35

Go Kart Torque Converter CVT Clutch ¾” Comet Tav2 30-75 218353A Manco 12T #35

 

This is a complete CVT clutch assembly. It comes with one drive belt, one plastic cover, a three quarter inch drive puller, a five eights inch drive pulley, an aluminum mounting plate, a twelve tooth sprocket that fits a number thirty five chain, the proper mounting hardware needed, and a ten tooth sprocket.

This torque converter will turn your racing bike into a speed demon. You will not need a lot of specialized tools to make the conversion from the clutch you already have in place to this high quality torque converter CVT clutch. The price is affordable, and the results of how your bike responds after the torque converter is installed will amaze you.

>> Check Out Verified Customer Reviews and Ratings <<

This item works on any compatible sized engine and does not require a specific brand of engine. A torque converter can be operated at low speeds and in low gears. This produces a lower gear ratio that makes your machine climb inclines with less effort, and produce higher rates of speed.

If you have  centrifugal clutch you will have to operate the engine at no less than five miles per hour or you will burn your clutch up. The torque converter can be worked at lower miles per hour without suffering any damages. 

Check Latest Price and Stock

 

7) Go Kart / Mini Bike Clutch # 35 chain ¾ Bore

Go kart / Mini Bike Clutch # 35 chain 3/4 Bore You will love the fact that this clutch is bi-directional. That means that you can mount the sprocket facing inward or mount the sprocket facing outward. You will get the same quality reaction from the clutch no matter which direction your bike needs to have the sprocket facing.

You also get the ability to use this assembly on numerous different brands of go karts, mini bikes, and similar equipment because of the ability to mount it either direction. If you find that the clutch is slow to engage when it is brand new you can heat the springs in the clutch a little using a blow torch.

>> Check Out Verified Customer Reviews and Ratings <<

This heat application will soften the spring material slightly and will allow the clutch to engage easier. This piece is made of high quality carbide steel that is rust resistant. You will not have to worry every time you run through a small puddle of water.

You should take all precautions to not let the riding machine sit outside in the weather any longer than you have to, but you do not have to fret if you get caught in the rain.

Check Latest Price and Stock

 

8) Prime Line 7-06002 Centrifugal Clutch for Mini-Bikes, Go-Karts, Riding Mowers, Snow Throwers and Garden Tractors

Prime Line 7-06002 Centrifugal Clutch for Mini-Bikes, Go-Karts, Riding Mowers, Snow Throwers and Garden Tractors This is an amazing clutch that is made from sintered steel. Sintered steel is created by taking powdered metal pieces below their normal melting point so that the molecules form a new type of bond. Once the sintering process is complete the product is steel that is resistant to high temperature damage and high temperatures do not cause the metal to lose its shape.

>> Check Out Verified Customer Reviews and Ratings <<

The clutch has a limited slip design included that engages at eighteen hundred rotations per minute. This allows your riding machine to run smoother without any hang-ups, or damages that can come when a clutch slips and allows the chain to slip.

The device is very easy to install on the three quarter inch engine shaft. Key stock will be used to hold the clutch in place, and you do not need anything more complicated than a pair of pliers to install it. You need no specialized tools, you do not need a lot of mechanical prowess, or to hire a professional mechanic to get the part in place. 

Check Latest Price and Stock

 

9) Go Kart 1 Inch Torque Converter Kit CVT Clutch Comet TAV2 Manco 10T 40/41 12T #35

Go Kart 1 This complete one inch torque converter set has a one year warranty guarantee from the manufacturer. It is made of high quality carbide steel that resists rusting, and I strong enough to handle high temperatures, and powerful engines. The kit includes all of the mounting hardware you will need to install the torque converter. It comes with an aluminum mounting plate and two sprockets.

>> Check Out Verified Customer Reviews and Ratings <<

You will get a twelve tooth sprocket and a ten tooth sprocket. You get the plastic cover and the drive belt, as well as the drive pulley you need to install the torque converter. It works on Manco parts and on Comet parts.

A lot of people put the torque converters on riding machines that once had centrifugal clutch assemblies because they wish to increase the amount of power, and speed their machine has, while reducing the gear ration and the response time the machine has. The result of the conversion is more power and speed, with less heat damage done to other working parts of the machine. 

Check Latest Price and Stock

 

10) Go Kart Clutch C41 10T for Hillard’s Extreme Duty

Go Kart Clutch C41 10T for Hillard's Extreme Duty To install this clutch you install a bolt on the end of the crankshaft of the engine. You will need a washer measuring one and one sixteenths of an inch on the outside portion of the washer. That will be the largest section of the washer.

Do not attempt to tighten the clutch until you ascertain that the engine is in the off position. This is for safety during installation. You need to tighten the bolt to the point that you are actually turning over the motor when you turn the bolt, and when you hold out on the starter out so that you can properly tighten the bolt.

>> Check Out Verified Customer Reviews and Ratings <<

You do not need any special tools, and you do not need a licensed auto mechanic to do the work for you. The extreme duty clutch will be able to withstand all of the punishment that riding over rough, uneven terrains can dish out.

You do not have to worry about dust damaging the working components, or about the clutch being easy to rust so you avoid water of all types while riding. You can ride where you want, when you want, and never give a second thought to the clutch, or to whether your engine will engage properly when you need it to. 

Check Latest Price and Stock

 

11) Go Kart Clutch C35 12 T for Hillard’s Extreme Duty

Go Kart Clutch C35 12t for Hillard's Extreme Duty If you want speed from your riding machine then you want an extreme duty clutch to help you engage the engine properly without losing any power. The extreme duty piece is crafted with high heat resistant carbide steel.

The steel is made to resist rust so you can ride your machine in water, in the rain, across wet grass, and in moist climates without being concerned. You simply oil the clutch and chain properly and this will keep the item working properly without rusting on the inside.

>> Check Out Verified Customer Reviews and Ratings <<

The clutch is sealed so you do not have to worry about dust on the road. The occasional oiling of the chain will remove any dust build-up so you can feel free to ride across the beach, or down a dirt road. These clutches are reasonably priced, and they have been designed so anyone can change them no matter how mechanically inclined you are.

You will need a pair of pliers, but few other tools to make the transition from old clutch to new clutch. You can expect this heavy duty item to last many years. You will have increased speed and a quicker response time from your machine that the engine is mounted on. The clutch will improve performance and help improve the amount of life you get from your engine. 

Check Latest Price and Stock

Final Thoughts

A centrifugal clutch is the most popular type of clutch on chainsaws, go karts, mini bikes, some lawn mowers, and some garden tractors. These pieces of equipment are low cost and they will last a long time if you maintain your machine properly. You want to oil the clutch bushing for every four hours of continuous operation. If you go ride all day then be sure you oil your bushing before you put your machine away. Before riding you should make it a habit to check the tension of the chain the alignment of the sprocket and the condition of the chain. This process will only take a few moments of your time, but it could save you a lot of costly repairs. Thanks for reading our Go Kart Clutch resource page . Feel free to share your ideas . We love to hear from you.  

Melissa Gibson
 

Melissa has been a technology writer for the last five years. She lives in New York City and during her vacation, you will find her riding scooters, reading books and hiking mountains.

Click Here to Leave a Comment Below 2 comments
Jason - last year

Hi I’m looking for a clutch for a 15hp honda engine GX 420 pull start ….can you help thank jason

Reply
    Melissa Gibson - last year

    We have listed 1-2 here in this article which may meet your criteria

    Reply

Leave a Reply: